What PSU for a NVIDIA GeForce RTX 5060 and Ryzen 5 7600?
Pairing a NVIDIA GeForce RTX 5060 (145 W board power) with a Ryzen 5 7600 (88 W peak) gives a system load of about 350 W. Both figures are verified against the manufacturers’ own specifications — the sources are linked below.
Recommendations are planning estimates, not electrical or purchasing advice. The hardware figures behind them are vendor-published; your exact board-partner model and build can still differ.
Recommended PSU
450 W
Leaves the supply at about 78% load under gaming.
Minimum
450 W
Smallest quality tier we would pair with this build.
System load
350 W
145 W GPU + 88 W CPU + 117 W rest of build.
GPU power connector
1× PCIe 8-pin
Plus the board’s EPS 12V cable for the CPU.
Where the power goes
The NVIDIA GeForce RTX 5060 is still the largest single draw at 145 W, but only 41% of the 350 W total — in a build this modest the processor (88 W) and the rest of the system together account for more than the card does. The remaining 117 W covers the board, memory, one SSD, three fans and a USB allowance.
GPU 41% · CPU 25% · rest of build 34%
Why 450 W
At 350 W this build sits inside the smallest quality tier we would recommend, so 450 W is the floor rather than a calculation about headroom. There is no sensible smaller unit to consider.
Graphics-card draw is not flat — brief peaks above the rated board power are normal, and a supply running close to its limit can trip on one. We do not publish a peak figure for the NVIDIA GeForce RTX 5060 because the manufacturer does not publish one. At 145 W a quality unit of the recommended wattage copes without drama; an ATX 3.x supply is a reasonable buy but not a requirement for this build.
Here the manufacturer is more cautious than we are: it recommends 550 W for the NVIDIA GeForce RTX 5060, while our maths with the Ryzen 5 7600 gives 450 W — 100 W lower. Vendor numbers are deliberately padded to cover weak supplies and heavier CPUs than this one. Treat 550 W as the safe retail answer and 450 W as what this specific build supports with a quality unit.
Cabling this build
The NVIDIA GeForce RTX 5060 takes 1× PCIe 8-pin, so cabling is simple: one lead from the supply, no splitters or adapters needed at 145 W. On top of that the board needs its EPS 12V CPU cable — one 8-pin is enough for the Ryzen 5 7600 at 88 W, though many boards expose a second socket you can leave empty.
Different case, more drives, or an AIO? Open the PSU Calculator with both parts pre-selected →
Figures above assume an ATX board, 2 RAM sticks, 1 SSD, 3 fans and a USB allowance, at the standard headroom profile.
Frequently asked questions
What PSU do you need for a NVIDIA GeForce RTX 5060 and Ryzen 5 7600?
We recommend a quality 450 W power supply. The pairing draws about 350 W under load — 145 W for the card, 88 W for the CPU and 117 W for the rest of a typical build — and 450 W is the smallest tier we would pair with it.
How much power does a NVIDIA GeForce RTX 5060 and Ryzen 5 7600 build use?
About 350 W under a combined gaming load, which is roughly 78% of the 450 W supply we recommend. That is a conservative figure built from vendor-published ceilings, so day-to-day draw is usually lower.
Is 550 W enough for a NVIDIA GeForce RTX 5060 and Ryzen 5 7600?
Yes — comfortably. 550 W is the card maker's padded figure; this build only needs 450 W by our maths, so a 550 W unit leaves plenty of margin.